VIP issue

 

Plear bear with me as i'm new to F5 so..needing much guidance with clarifications

 

 

[root@ve10:Active] config b virtual vl100-bz profiles { clientssl tcp }

 

 

Just simply applying the above command it will overwrite the xfwrd profile and replace it with clientssl?

 

 

also, say, if i were asked to remove only xfrwrd profile and retain rest of the Virtual as it is, what single command with bigpipe i need to use to remove the xfrwrd profile from the VIP w/ touching any other part of VS.

 

Just simply applying the above command it will overwrite the xfwrd profile and replace it with clientssl?actually, it will replace all existing profiles with the one in the command line (clientssl and tcp).

also, say, if i were asked to remove only xfrwrd profile and retain rest of the Virtual as it is, what single command with bigpipe i need to use to remove the xfrwrd profile from the VIP w/ touching any other part of VS. e.g.

[root@ve10:Active] config  b virtual vl100-bz list
virtual vl100-bz {
   snatpool bz-vl100
   pool bz-pl
   destination 172.20.10.50:443
   ip protocol 6
   persist persist-profile
   profiles {
      http-xforward {}
      tcp {}
   }
   vlans vlan100 enable
}

[root@ve10:Active] config  b virtual vl100-bz profile http-xforward delete

[root@ve10:Active] config  b virtual vl100-bz list
virtual vl100-bz {
   snatpool bz-vl100
   pool bz-pl
   destination 172.20.10.50:443
   ip protocol 6
   persist persist-profile
   vlans vlan100 enable
}

ps. tcp profile is not shown after deleting http-xforward profile because it is default one.

by the way, if you are not familiar with bigpipe command, i suggest trying tmsh. it would be easier since there is feature such as context sensitive help, tab-completion.

v.10 Introduction to the tmsh Command Shell by Don Mac Vittie

https://devcentral.f5.com/tech-tips/articles/v10-introduction-to-the-tmsh-command-shell

if tcp was not a default profile but a custom profile, then it would not get deleted ..right?

 

 

also,what would be the command to add the xfrwrd profile back to Virtual.

 

 

if tcp was not a default profile but a custom profile, then it would not get deleted ..right? it is not deleted. it is just not shown because it is default profile.

 

 

also,what would be the command to add the xfrwrd profile back to Virtual. just replacing "delete" with "add". :-)

thank you so much nitass for your patient replies and bearing with my clarifications.

 

 

is there any single command in bigip to see all the running configuration, just like " show run".

is there any single command in bigip to see all the running configuration, just like " show run".there is show running-config in tmsh.

root@ve10(Active)(tmos) show ?
Options:
  current-module  Do not recurse into sub-modes
  running-config  Display configuration settings
  |               Route command output to a filter
Modules:
  auth            User accounts and authentication
  cli             Local user settings and configuration transactions
  gtm             Global Traffic Manager
  ltm             Local Traffic Manager
  net             Network configuration
  sys             General system configuration
  wom             WAN Optimization

any command in bigpipe to see full run-config?

any command in bigpipe to see full run-config?if one command, can you try "b export"? otherwise, you may try "b base list" and "b list".

 

 

Bigpipe Utility Reference Guide

 

http://support.f5.com/content/kb/en-us/products/big-ip_ltm/manuals/product/bigip_utility_reference_guide_10_1_0/_jcr_content/pdfAttach/download/file.res/Bigpipe_Utility_Reference_Guide.pdf

 

 

sol8435: Overview of Single Configuration Files (9.x - 10.x)

 

http://support.f5.com/kb/en-us/solutions/public/8000/400/sol8435.html