Software Installation aborting at about 97%
Hello, I want to update a Virtual F5 from 14.1.2.3to 14.1.2.4. but when install-process reaches about 97% the GUI reloads. I've tried it from the CLI: the same, I see the Messages about restarting cbrd, apm_websso0, dynconfd, ... the diskspace should be fine: Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg--db--sda-set.2.root 419M 78M 315M 20% / devtmpfs 3.9G 4.0K 3.9G 1% /dev tmpfs 3.9G 2.3M 3.9G 1% /dev/shm tmpfs 3.9G 2.2M 3.9G 1% /run tmpfs 3.9G 0 3.9G 0% /sys/fs/cgroup /dev/mapper/vg--db--sda-set.2._usr 5.0G 4.0G 761M 85% /usr /dev/mapper/vg--db--sda-set.2._config 2.1G 1.4G 626M 69% /config /dev/mapper/vg--db--sda-set.2._var 2.9G 1.3G 1.5G 47% /var none 3.9G 19M 3.9G 1% /var/tmstat prompt 4.0M 28K 4.0M 1% /var/prompt /dev/mapper/vg--db--sda-dat.appdata 25G 961M 23G 5% /appdata /dev/mapper/vg--db--sda-dat.share 20G 5.9G 13G 32% /shared none 3.9G 30M 3.9G 1% /shared/rrd.1.2 /dev/mapper/vg--db--sda-dat.log 2.9G 180M 2.6G 7% /var/log none 3.9G 0 3.9G 0% /var/loipc /dev/loop0 298M 298M 0 100% /var/apm/mount/apmclients-7182.2019.923.1603-4727.0.iso any Ideas, where to look for? another virtual F5 updatet the same Version without problems
Move to standby all vcmps to update HOST (VIPRION)
Hello, Is there a way to force all vcmps to standby? I have 2 VIPRION and I want to re-license one of them previous to upgrade the BIG-IP version running on it. So I need to move all guests from one Host to other VIPRION to prevent loss of service. Running the following command you can see the state; active or standby, for all vcmps: # tmsh show vcmp | sed '/Vcmp::Guest Prompt/,/^$/!d' I´m trying to failover from HOSTA to HOSTB all guest with status: /Sn-green-P:Active. Is this possible?
Update 11.5.1. HF4 to HF6 fails with configuration problem - BUG
Hi, There seems to be a bug in the new Hotfix! After the update from HF4 to HF6 and a reboot, I get the know error message "The configuration has not yet loaded. If this message persists, it may indicate a configuration problem." The ASM module will be stopped. If I run "tmsh load sys conf", I get Syntax Error:(/config/bigip.conf at line: 112) "predefined-report-name" may not be specified with "multi-leveled-report.limit" If I look into the conf on the activ device, I find "predefined-report-name" in my configured analytics reports (Security/Application/Charts Scheduler). Strange: If I delete the scheduler on the active device, it will still exist in the config on the active device, but it will be removeed from the config of the standby device. If I create a new one and delete it again, everything is removed from the config. An update without a any chart scheduler and a clean bigip.conf results in another error. Now, I get 010717e1:3: Client SSL profile cannot contain more than one set of same certificate/key type. Unexpected Error: Loading configuration process failed. This is described here: https://devcentral.f5.com/questions/010717e13-client-ssl-profile-cannot-contain-more-than-one-set-of-same-certificate-key-type This is a bad hotfix. Be careful.
configuration error after upgrading to 13.1.1
Hi, just updated our F5 from 12.1.2 to 13.1.1. Unfortunately I have an issue with one VS in the internal partition, it is disabled and it's not possible to enable it. The error that occurs is following: Configuration error: Virtual server (/Internal/Exchange2010-Internal.app/Exchange2010-Internal_combined_https) with access profile attached has traffic group (/Common/Internal-TG) that is different from existing one (/Common/External-TG) We have 2 partitions (Internal / External) and also 2 traffic-groups (Internal-TG / External-TG), where all the VS are assigned properly. With 12.0 / 12.1 everything worked fine, also after updates. Now, after upgrading from 12.1.2 to 13.1.1 this error occurred, but only in the internal partition. The External one has also an OWA-VS created with the same iApp - everything ok there. I checked all the configuration, unfortunately I can't find anything that could be wrong by myself. The configuration was done with an iApp and later some changes were made, but nothing special and nothing that could describe such an issue. Any ideas?
PHONEHOME: Update Server unavailable
Recently i have started seeing this error. What is this about? If F5 checking for updates then how to check which server its connecting etc and where are the proper place to check logs I found following logs in Logs > LTM Tue Oct 6 04:03:10 EDT 2015infolbf5updatecheck[12466] PHONEHOME: Update Server unavailable
active/stanby cluster disconnected after Update
I have two new F5 BIG IPs with 12.1.2 HF2 installed, these two devices are running active/standby (same device trust configuration like the old ones with 11.6.2 HF1). While Upgrading from 12.1.2 to 12.1.3.1 (or directly to 13.0.0 or 13.1.0) my Cluster ist disconnected, because of different Software Version. Does any one have the same issue? Any suggestions?f5 update check manually working but not automatic
We have LTM 1600 in pair (A and B) System ›› Software Management : Update Check I have checked firewall/DNS etc.. everything working fine. I did telnet (443 port) and it works. A - Automatically working OK B - Automatically not working. But if i do manual check, it works!. How do i find out what and where is wrong?F5 update check issue
We have "Update check" Enabled on F5 and its weekly schedule but in same page it is showing. Why it is saying last update was on 2014? Last Checked Version11.6.0.0.0.401 Latest Update CheckFri Dec 26 04:02:09 EST 2014 (Automatic) Available UpdateSoftware is up-to-date. Available HotfixHotfix-BIGIP-11.6.0.2.0.405-HF2 iso installation file Geo Location Software Version Last Checked Version1.0.1-20140703.99.0 Latest Update CheckFri Dec 26 04:02:09 EST 2014 (Automatic) Available Updateip-geolocation-1.0.1-20141204.119.0 End User Diagnostics (EUD) Software Version Last Checked Version2.6.0.8.0 Latest Update CheckFri Dec 26 04:02:09 EST 2014 (Automatic) Available UpdateEUD_T-2.6.0.9.0.iso
Proxy Setting for Image Update Check
Hi, I have tried adding the proxy setting to the: services.ini Database tmsh modify sys db proxy.host value hostname tmsh modify sys db proxy.port value port_number But it still try to go direct for the software update check. Any ideas where I should be adding it?
