aci
33 TopicsF5 LTM with cisco ACI applied multi-site
Dears, if anyone used F5 LTM with Cisco ACI, I have just one question when the ACI makes Multi-site and the server replicated to the other datacenter with the same IP, how can I configure this in the LTM or if this require me to make any change on the F5 LTM23Views0likes0CommentsF5 and Cisco ACI Essentials - Design guide for a Single Pod APIC cluster
Deployment considerations It is usually an easy decision to have BIG-IP as part of your ACI deployment as BIG-IP is a mature feature rich ADC solution. Where time is spent is nailing down the design and the deployment options for the BIG-IP in the environment. Below we will discuss a few of the most commonly asked questions: SNAT or no SNAT There are various options you can use to insert the BIG-IP into the ACI environment. One way is to use the BIG-IP as a gateway for servers or as a routing next hop for routing instances. Another option is to use Source Network Address Translation (SNAT) on the BIG-IP, however with enabling SNAT the visibility into the real source IP address is lost. If preserving the source IP is a requirement then ACI's Policy-Based Redirect (PBR) can be used to make sure the return traffic goes back to the BIG-IP. BIG-IP redundancy F5 BIG-IP can be deployed in different high-availability modes. The two common BIG-IP deployment modes: active-active and active-standby. Various design considerations, such as endpoint movement during fail-overs, MAC masquerade, source MAC-based forwarding, Link Layer Discovery Protocol (LLDP), and IP aging should also be taken into account for each of the deployment modes. Multi-tenancy Multi-tenancy is supported by both Cisco ACI and F5 BIG-IP in different ways. There are a few ways that multi-tenancy constructs on ACI can be mapped to multi-tenancy on BIG-IP. The constructs revolve around tenants, virtual routing and forwarding (VRF), route domains, and partitions. Multi-tenancy can also be based on the BIG-IP form factor (appliance, virtual edition and/or virtual clustered multiprocessor (vCMP)). Tighter integration Once a design option is selected there are questions around what more can be done from an operational or automation perspective now that we have a BIG-IP and ACI deployment? The F5 ACI ServiceCenter is an application developed on the Cisco ACI App Center platform built for exactly that purpose. It is an integration point between the F5 BIG-IP and Cisco ACI. The application provides an APIC administrator a unified way to manage both L2-L3 and L4-L7 infrastructure. Once day-0 activities are performed and BIG-IP is deployed within the ACI fabric using any of the design options selected for your environment, then the F5 ACI ServiceCenter can be used to handle day-1 and day-2 operations. The day-1 and day-2 operations provided by the application are well suited for both new/greenfield and existing/brownfield deployments of BIG-IP and ACI deployments. The integration is loosely coupled, which allows the F5 ACI ServiceCenter to be installed or uninstalled with no disruption to traffic flow, as well as no effect on the F5 BIG-IP and Cisco ACI configuration. Check here to find out more. All of the above topics and more are discussed in detail here in the single pod white paper.1.7KViews3likes0CommentsF5 & Cisco ACI Essentials - Dynamic pool sizing using the F5 ACI ServiceCenter
APIC EndPoints and EndPoint Groups When dealing with the Cisco ACI environment you may have wondered about using an Application-Centric Design or a Network-Centric Design. Regardless of the strategy, the ultimate goal is to have an accessible and secure application/workload in the ACI environment. An application is comprised of several servers; each one performing a function for the application (web server, DB server, app server etc.). Each of these servers may be physical or virtual and are treated as endpoints on the ACI fabric. Endpoints are devices connected to the network directly or indirectly. They have an address, attributes and can be physical or virtual. Endpoint examples include servers, virtual machines, network-attached storage, or clients on the Internet. An EPG (EndPoint Group) is an object that contains a collection of endpoints, which can be added to an EPG either dynamically or statically. Take a look at the relationship between different objects on the APIC. Click here for more details. Relationship between Endpoints and Pool members If an application is being served by web servers with IPs having address's in the range 192.168.56.*, for example, then these IP addresses will be presented as an endpoint in an endpoint group (EPG) on the APIC. From the perspective of BIG-IP, these web servers are pool members of a particular pool. The F5 ACI ServiceCenter is an application developed on the Cisco ACI App Center platform designed to run on the APIC controller. It has access to both APIC and BIG-IP and can correlate existing information from both devices to provide a mapping as follows: BIG-IP | APIC ________________________________________________________________________ VIP: Pool: Pool Member(s): Route Domain (RD) |Tenant: Application Profile: End Point group: Virtual Routing and Forwarding (VRF) This gives an administrator a view of how the APIC workload is associated with the BIG-IP and what all applications and virtual IP's are tied to a tenant. Click here for more details on this visibility dashboard and learn more on how and under what situations the dashboard can be helpful. In this article we are going to see how the F5 ACI ServiceCenter can take advantage of the endpoints learned by the ACI fabric to dynamically grow/shrink pool members. Dynamic EndPoint Attach and Detach Let's think back to our application which is say being hosted on 100's of servers, these servers could be added to an APIC EPG statically by a network admin or they could be added dynamically through a vCenter or openstack APIC integration. In either case, these endpoints ALSO need to be added to the BIG-IP where the endpoints can be protected by malicious attacks and/or load-balanced. This can be a very tedious task for a APIC or a BIG-IP administrator. Using the dynamic EndPoint attach and detach feature on the F5 ACI ServiceCenter, this burden can be reduced. The application has the ability to adjust the pool members on the BIG-IP based on the server farm on the APIC. On APIC when an endpoint is attached, it is learned by the fabric and added to a particular tenant, application profile and EPG on the APIC. The F5 ACI ServiceCenter provides the capability to map an EPG on the APIC to a pool on the BIG-IP. The application relies on the attach/detach notifications from the APIC to add/delete the BIG-IP pool-members. There are different ways in which the dynamic mapping can be leveraged using the F5 ACI ServiceCenter based on the L4-L7 configuration: Scenario 1: Declare L4-L7 configuration using F5 ACI ServiceCenter Scenario 2: L4-L7 configuration already exists on the BIG-IP Scenario 3: Use dynamic mapping but do not declare the L4-L7 configuration using the F5 ACI ServiceCenter Scenario 4: Use the F5 ACI ServiceCenter API's to define the mapping along with the L4-L7 configuration Let's take a look at each one of them in detail. Scenario 1: Declare L4-L7 configuration using F5 ACI ServiceCenter Let's assume there is no existing configuration on the BIG-IP, a new application needs to be deployed which is front ended by a VIP/Pool/Pool members. The F5 ACI ServiceCenter provides a UI that can be used to deploy the L4-L7 configuration and create a mapping between Pool <-> EPG. There are two options: Basic mode uses FAST andAdvanced mode uses AS3. Basic mode: Leverage dynamic endpoint attach and detach feature by using the pre-built Service-Discovery template Advanced mode: Leverage dynamic endpoint attach and detach feature by using Manage Endpoint Mappings Scenario 2: L4-L7 configuration already exists on the BIG-IP If L4-L7 configuration using AS3 already exists on the BIG-IP, the F5 ACI ServiceCenter will detect all partitions and application that in compatible with AS3. Configuration for a particular partition/application on BIG-IP can then be updated to create a Pool <-> EPG mapping. However, there is one condition that is the pool can either have static or dynamic members. Thus, if the pool already has existing members, those members will have to be deleted before a dynamic mapping can be created. To maintain the dynamic mapping, any future changes to the L4-L7 configuration on the BIG-IP should be done via the F5 ACI ServiceCenter. Scenario 3: Use dynamic mapping but do not declare the L4-L7 configuration using the F5 ACI ServiceCenter The F5 ACI ServiceCenter can be used just for the dynamic mapping and pool sizing and not for defining the L4-L7 configuration. For this method, the entire AS3 declaration along with the mapping will be directly send to the BIG-IP using AS3. Since the declaration is AS3, the F5 ACI ServiceCenter will automatically detect a Pool <-> EPG mapping which can be viewable from the inventory tab. Step 1: AS3 declaration with Pool <-> EPG mapping posted directly to the BIG-IP (see below for a sample declaration) Step 2: Sync Endpoints Step 3: View Endpoints Scenario 4: Use the F5 ACI ServiceCenter API's to define the mapping along with the L4-L7 configuration Finally, if the UI is not appealing and automation all the way is the goal, then the F5 ACI ServiceCenter has an API call where the mapping as well as the L4-L7 configuration (which was done in Scenario 1) can be completely automated: URI: https://<apic_controller_ip>>/appcenter/F5Networks/F5ACIServiceCenter/updateas3data.json In this scenario, the declaration is being passed to the F5 ACI ServiceCenter through the APIC controller and NOT directly to the BIG-IP. A sample API call Summary Having knowledge on how AS3 works is essential since it is a declarative API, and using it incorrectly can result in incorrect configuration. Any method mentioned above would work, and the decision on which method to use is based on the operational model that works the best in your environment. References Unify Visibility with F5 ACI ServiceCenter in Cisco ACI and F5 BIG-IP Deployments Download F5 ACI ServiceCenter F5 ACI ServiceCenter API documentation F5 AS3 - What does it means -imperative vs declarative F5 AS3 Best Practice Cisco ACI Fabric Endpoint Learning White Paper782Views1like0CommentsF5 & Cisco ACI Essentials - Take advantage of Policy Based Redirect
Different applications and environments have unique needs on how traffic is to be handled. Some applications due to the nature of their functionality or maybe due to a business need do require that the application server(s) are able to view the real IP of the client making the request to the application. Now when the request comes to the BIG-IP it has the option to change the real IP of the request or to keep it intact. In order to keep it intact the setting on the F5 BIG-IP ‘Source Address Translation’ is set to ‘None’. Now as simple as it may sound to just toggle a setting on the BIG-IP, a change of this setting causes significant change in traffic flow behavior. Let’s take an example with some actual values. Starting with a simple setup of a standalone BIG-IP with one interface on the BIG-IP for all traffic (one-arm) Client – 10.168.56.30 BIG-IP Virtual IP – 10.168.57.11 BIG-IP Self IP – 10.168.57.10 Server – 192.168.56.30 Scenario 1: With SNAT From Client : Src: 10.168.56.30 Dest: 10.168.57.11 From BIG-IP to Server: Src: 10.168.57.10 (Self-IP) Dest: 192.168.56.30 With this the server will respond back to 10.168.57.10 and BIG-IP will take care of forwarding the traffic back to the client. Here the application server see’s the IP 10.168.57.10 and not the client IP Scenario 2: No SNAT From Client : Src: 10.168.56.30 Dest: 10.168.57.11 From BIG-IP to Server: Src: 10.168.56.30 Dest: 192.168.56.30 With this the server will respond back to 10.168.56.30 and here where comes in the complication, the return traffic needs to go back to the BIG-IP and not the real client. One way to achieve this is to set the default GW of the server to the Self-IP of the BIG-IP and then the server will send the return traffic to the BIG-IP. BUT what if the server default gateway is not to be changed for whatsoever reason. It is at this time Policy based redirect will help. The default gw of the server will point to the ACI fabric, the ACI fabric will be able to intercept the traffic and send it over to the BIG-IP. With this the advantage of using PBR is two-fold The server(s) default gateway does not need to point to BIG-IP but can point to the ACI fabric The real client IP is preserved for the entire traffic flow Avoid server originated traffic to hit BIG-IP, resulting BIG-IP to configure a forwarding virtual to handle that traffic.If server originated traffic volume is high it could result unnecessary load the BIG-IP Before we get to the deeper into the topic of PRB below are a few links to help you refresh on some of the Cisco ACI and BIG-IP concepts ACI fundamentals: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/1-x/aci-fundamentals/b_ACI-Fundamentals.html SNAT and Automap: https://support.f5.com/csp/article/K7820 BIG-IP modes of deployment: https://support.f5.com/csp/article/K96122456#link_02_01 Now let’s look at what it takes to configure PBR using a Standalone BIG-IP Virtual Edition in One-Arm mode Network diagram for reference: To use the PBR feature on APIC - Service graph is a MUST Details on L4-L7 service graph on APIC To get hands on experience on deploying a service graph (without pbr) Configuration on APIC 1) Bridge domain ‘F5-BD’ Under Tenant->Networking->Bridge domains->’F5-BD’->Policy IP Data plane learning - Disabled 2) L4-L7 Policy-Based Redirect Under Tenant->Policies->Protocol->L4-L7 Policy based redirect, create a new one Name: ‘bigip-pbr-policy’ L3 destinations: BIG-IP Self-IP and MAC IP: 10.168.57.10 MAC: Find the MAC of interface the above Self-IP is assigned from logging into the BIG-IP (example: 00:50:56:AC:D2:81) 3) Logical Device Cluster- Under Tenant->Services->L4-L7, create a logical device Managed – unchecked Name: ‘pbr-demo-bigip-ve` Service Type: ADC Device Type: Virtual (in this example) VMM domain (choose the appropriate VMM domain) Devices: Add the BIG-IP VM from the dropdown and assign it an interface Name: ‘1_1’, VNIC: ‘Network Adaptor 2’ Cluster interfaces Name: consumer, Concrete interface Device1/[1_1] Name: provider, Concrete interface: Device1/[1_1] 4) Service graph template Under Tenant->Services->L4-L7->Service graph templates, create a service graph template Give the graph a name:’ pbr-demo-sgt’ and then drag and drop the logical device cluster (pbr-demo-bigip-ve) to create the service graph ADC: one-arm Route redirect: true 5) Click on the service graph created and then go to the Policy tab, make sure the Connections for the connectors C1 and C2 and set as follows: Connector C1 Direct connect – False (Not mandatory to set to 'True' because PBR is not enabled on consumer connector for the consumer to VIP traffic) Adjacency type – L3 Connector C2 Direct connect - True Adjacency type - L3 6) Apply the service graph template Right click on the service graph and apply the service graph Choose the appropriate consumer End point group (‘App’) provider End point group (‘Web’) and provide a name for the new contract For the connector select the following: BD: ‘F5-BD’ L3 destination – checked Redirect policy – ‘bigip-pbr-policy’ Cluster interface – ‘provider’ Once the service graph is deployed, it is in applied state and the network path between the consumer, BIG-IP and provider has been successfully setup on the APIC. 7) Verify the connector configuration for PBR. Go to Device selection policy under Tenant->Services-L4-L7. Expand the menu and click on the device selection policy deployed for your service graph. For the consumer connector where PBR is not enabled Connector name - Consumer Cluster interface - 'provider' BD- ‘F5-BD’ L3 destination – checked Redirect policy – Leave blank (no selection) For the provider connector where PBR is enabled: Connector name - Provider Cluster interface - 'provider' BD - ‘F5-BD’ L3 destination – checked Redirect policy – ‘bigip-pbr-policy’ Configuration on BIG-IP 1) VLAN/Self-IP/Default route Default route – 10.168.57.1 Self-IP – 10.168.57.10 VLAN – 4094 (untagged) – for a VE the tagging is taken care by vCenter 2) Nodes/Pool/VIP VIP – 10.168.57.11 Source address translation on VIP: None 3)iRule (end of the article) that can be helpful for debugging Few differences in configuration when the BIG-IP is a Virtual edition and is setup in a High availability pair 1)BIG-IP: Set MAC Masquerade (https://support.f5.com/csp/article/K13502) 2)APIC: Logical device cluster Promiscuous mode – enabled Add both BIG-IP devices as part of the cluster 3) APIC: L4-L7 Policy-Based Redirect L3 destinations: Enter the Floating BIG-IP Self-IP and MAC masquerade ------------------------------------------------------------------------------------------------------------------------------------------------------------------ Configuration is complete, let’s take a look at the traffic flows Client-> F5 BIG-IP -> Server Server-> F5 BIG-IP -> Client In Step 2 when the traffic is returned from the client, ACI uses the Self-IP and MAC that was defined in the L4-L7 redirect policy to send traffic to the BIG-IP iRule to help with debugging on the BIG-IP when LB_SELECTED { log local0. "==================================================" log local0. "Selected server [LB::server]" log local0. "==================================================" } when HTTP_REQUEST { set LogString "[IP::client_addr] -> [IP::local_addr]" log local0. "==================================================" log local0. "REQUEST -> $LogString" log local0. "==================================================" } when SERVER_CONNECTED { log local0. "Connection from [IP::client_addr] Mapped -> [serverside {IP::local_addr}] \ -> [IP::server_addr]" } when HTTP_RESPONSE { set LogString "Server [IP::server_addr] -> [IP::local_addr]" log local0. "==================================================" log local0. "RESPONSE -> $LogString" log local0. "==================================================" } Output seen in /var/log/ltm on the BIG-IP, look at the event <SERVER_CONNECTED> Scenario 1: No SNAT -> Client IP is preserved Rule /Common/connections <HTTP_REQUEST>: Src: 10.168.56.30 -> Dest: 10.168.57.11 Rule /Common/connections <SERVER_CONNECTED>: Src: 10.168.56.30 Mapped -> 10.168.56.30 -> Dest: 192.168.56.30 Rule /Common/connections <HTTP_RESPONSE>: Src: 192.168.56.30 -> Dest: 10.168.56.30 If you are curious of the iRule output if SNAT is enabled on the BIG-IP - Enable AutoMap on the virtual server on the BIG-IP Scenario 2: With SNAT -> Client IP not preserved Rule /Common/connections <HTTP_REQUEST>: Src: 10.168.56.30 -> Dest: 10.168.57.11 Rule /Common/connections <SERVER_CONNECTED>: Src: 10.168.56.30 Mapped -> 10.168.57.10-> Dest: 192.168.56.30 Rule /Common/connections <HTTP_RESPONSE>: Src: 192.168.56.30 -> Dest: 10.168.56.30 References: ACI PBR whitepaper: https://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/application-centric-infrastructure/white-paper-c11-739971.html Troubleshooting guide: https://www.cisco.com/c/dam/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/troubleshooting/Cisco_TroubleshootingApplicationCentricInfrastructureSecondEdition.pdf Layer4-Layer7 services deployment guide https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/L4-L7-services/Cisco-APIC-Layer-4-to-Layer-7-Services-Deployment-Guide-401/Cisco-APIC-Layer-4-to-Layer-7-Services-Deployment-Guide-401_chapter_011.html Service graph: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/L4-L7-services/Cisco-APIC-Layer-4-to-Layer-7-Services-Deployment-Guide-401/Cisco-APIC-Layer-4-to-Layer-7-Services-Deployment-Guide-401_chapter_0111.html https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/L4-L7-services/Cisco-APIC-Layer-4-to-Layer-7-Services-Deployment-Guide-401.pdf2.6KViews1like3CommentsF5 & Cisco ACI Essentials - ServiceCenter: One stop shop for IP address facts
Having to debug a network issue can be a daunting task, involving 100's of IP address's spread acrossyour entire deployment. Imagine having a tool which can help with getting all the information you want of an IP address with a click of a button. The F5 ACI ServiceCenter is one such tool designed to do exactly that and more. To refresh your knowledge on the tool: Lightboard Video Troubshooting tips User and deployment guide Telemetry streaming Let's get into the nuts and bolts of getting the entire benefit from visibility from the ServiceCenter. BIG-IP has a great component as part of its automation toolchain called 'Telemetry streaming'. The ServiceCenter takes advantage of telemetry streaming (TS) to grab traffic statistics from the BIG-IP. Integration TS with the ServiceCenter is a two step process: Step 1: Download and install the TS RPM package on the BIG-IP(no cost, no license) Step 2:Configure the TS consumer on the BIG-IP which the ServiceCenter will poll. Use a tool like POSTMAN or Curl to POST the below API to the BIG-IP. URI: https://<BIG-IP MGMT IP address>/mgmt/shared/telemetry/declare Payload: { "class":"Telemetry", "My_Poller":{ "class":"Telemetry_System_Poller", "interval":0, "actions":[ { "includeData":{ }, "locations":{ "virtualServers":{ ".*":{ } }, "pool":{ ".*":{ } } } } ] }, "My_System":{ "class":"Telemetry_System", "enable":"true", "systemPoller":[ "My_Poller" ] }, "My_Pull_Consumer":{ "class":"Telemetry_Pull_Consumer", "type":"default", "systemPoller":[ "My_Poller" ] } } IP Address facts Once logged into the ServiceCenter from the APIC controller choose the telemetry consumer to retrieve the IP address statistics. Conclusion The ServiceCenter besides the statistics will give much more information like the active connections on the BIG-IP, the physical port on which the IP is active (Virtual IP or node IP) on both the BIG-IP and the Cisco ACI, filtered logs from the BIG-IP and much more. To learn more check out the video below on the latest App enhancements and example use cases: Download the App to get started: https://dcappcenter.cisco.com/f5-aci-servicecenter.html746Views2likes2CommentsF5 and Cisco ACI Essentials: Automate automate automate !!!
This article will focus on automation support by BIG-IP and Cisco ACI and how automation tools specifically Ansible can be used to automate different use cases. Before getting into the weeds let's discuss and understand BIG-IP's and Cisco ACI's automation strategies. BIG-IP automation strategy BIG-IP automation strategy is simple-abstract as much complexity as possible from the user, give an easy button to the user to deploy their BIG-IP configuration. This could honestly mean different methods to different people, some prefer sending a single API call to perform one action( A one-to-one mapping between your API<->Configuration). Others prefer a more declarative approach where one API call performs multiple actions, basically a one-to -many mapping between your API(1)<->Configuration(N). A great link to refresh and learn about the different options: https://www.f5.com/products/automation-and-orchestration Cisco ACI automation strategy Cisco Application Policy Infrastructure Controller (APIC) is the network controller for the ACI fabric. APIC is the unified point of automation and management for the Cisco ACI fabric, policy enforcement, and health monitoring. The Cisco ACI programmability model provides complete programmatic access using APIC. Click here to learn more https://developer.cisco.com/site/aci/ Automation tools There are a lot of automation tools that are being talked for network automation BUT the one that comes up in every customer conversation is Ansible. Its simplicity, maturity and community adoption has made it very popular. In this article we are going to focus on using Ansible to automate a service discovery use case. Use Case: Dynamic EP attach/detach Let’s take an example of a simple http web service being made highly available and secure using the BIG-IP Virtual IP address. This web service has a bunch of backend web servers hosting the application, the IP of this web servers is configured on the BIG-IP as pool members. These same web server IP’s are learned as endpoints in the ACI fabric and are part of an End Point Group (EPG) on the APIC. Hence there is a logical mapping between a EPG on APIC and a pool on the BIG-IP. Now if the application is adding or deleting web servers that is hosting the application maybe to save cost or maybe to deal with increase/decrease of traffic, what happens is that the web server IP will be automatically learned/unlearned on APIC. BUT an admin will still have to add/remove that web server IP from the pool on BIG-IP. This can be a burden on the network admin specially if this happens very often. Here is where automation can help and let’s look at how in the next section More details on the use case can be found at https://devcentral.f5.com/s/articles/F5-Cisco-ACI-Essentials-Dynamic-pool-sizing-using-the-F5-ACI-ServiceCenter Automation of Use Case: Dynamic EP attach/detach Automation can be achieved by using Ansible and Ansible tower where API calls are made directly to the BIG-IP. Another option it to use the F5 ACI ServiceCenter (a native F5 ACI integration) to automate this particular use case. Ansible and Ansible tower To learn more about Ansible and Ansible tower: https://www.ansible.com/products/tower Using this method of automation separate API calls are made directly to the ACI and the BIG-IP. Sample playbook to perform the addition and deletion of pool members to a BIG-IP pool based on members in a particular EPG. The mapping of pool to EPG is provided as input to the playbook. - name: Dynamic end point attach/dettach hosts: aci connection: local gather_facts: false vars: epg_members: [] pool_members: [] pool_members_ip: [] bigip_ip: 10.192.73.xx bigip_password: admin bigip_username: admin # Here we are mapping pool 'dynamic_pool' to EPG 'internalEPG' which belongs to APIC tenant 'TenantDemo' app_profile_name: AppProfile epg_name: internalEPG partition: Common pool_name: dynamic_pool pool_port: 80 tenant_name: TenantDemo tasks: - name: Setup provider set_fact: provider: server: "{{bigip_ip}}" user: "{{bigip_username}}" password: "{{bigip_password}}" server_port: "443" validate_certs: "false" - name: Get end points learned from End Point group aci_rest: action: "get" uri: "/api/node/mo/uni/tn-{{tenant_name}}/ap-{{app_profile_name}}/epg-{{epg_name}}.json?query-target=subtree&target-subtree-class=fvIp" host: "{{inventory_hostname}}" username: "{{ lookup('env', 'ANSIBLE_NET_USERNAME') }}" password: "{{ lookup('env', 'ANSIBLE_NET_PASSWORD') }}" validate_certs: "false" register: eps - name: Get the IP's of the servers part of the EPG set_fact: epg_members="{{epg_members + [item]}}" loop: "{{eps | json_query(query_string)}}" vars: query_string: "imdata[*].fvIp.attributes.addr" no_log: True - name: Get only the IPv4 IP's set_fact: epg_members="{{epg_members | ipv4}}" - name: Adding Pool members to the BIG-IP bigip_pool_member: provider: "{{provider}}" state: "present" name: "{{item}}" host: "{{item}}" port: "{{pool_port}}" pool: "{{pool_name}}" partition: "{{partition}}" loop: "{{epg_members}}" - name: Query BIG-IP facts bigip_device_facts: provider: "{{provider}}" gather_subset: - ltm-pools register: bigip_facts - name: "Show members belonging to pool {{pool_name}}" set_fact: pool_members="{{pool_members + [item]}}" loop: "{{bigip_facts.ltm_pools | json_query(query_string)}}" vars: query_string: "[?name=='{{pool_name}}'].members[*].name[]" - set_fact: pool_members_ip: "{{pool_members_ip + [item.split(':')[0]]}}" loop: "{{pool_members}}" - debug: "msg={{pool_members_ip}}" #If there are any membeers on the BIG-IP that are not present in the EPG,then delete them - name: Find the members to be deleted if any set_fact: members_to_be_deleted: "{{ pool_members_ip | difference(epg_members) }}" - debug: "msg={{members_to_be_deleted}}" - name: Delete Pool members from the BIG-IP bigip_pool_member: provider: "{{provider}}" state: "absent" name: "{{item}}" port: "{{pool_port}}" pool: "{{pool_name}}" preserve_node: yes partition: "{{partition}}" loop: "{{members_to_be_deleted}}" Ansible tower's scheduling feature can be used to schedule this playbook to be run every minute, every hour or once per day based on how often an application is expected to change and how important is it for the configuration on both the Cisco ACI and the BIG-IP to be in sync. F5 ACI ServiceCenter To learn more about the integration : https://www.f5.com/cisco The F5 ACI ServiceCenter is installed on the APIC controller. Here automation can be used to create the initial EPG to Pool mapping. Once the mapping is created the F5 ACI ServiceCenter handles the dynamic sizing of pools based on events generated by APIC. Events are generated when a server is learned/unlearned on an EPG which is what the F5 ACI ServiceCenter listens to and accordingly adds or removes pool members from the BIG-IP. Sample playbook to deploy the mapping configuration on the BIG-IP through the F5 ACI ServiceCenter --- - name: Deploy EPG to Pool mapping hosts: localhost gather_facts: false connection: local vars: apic_ip: "10.192.73.xx" big_ip: "10.192.73.xx" partition: "Dynamic" tasks: - name: Login to APIC uri: url: https://{{apic_ip}}/api/aaaLogin.json method: POST validate_certs: no body_format: json body: aaaUser: attributes: name: "admin" pwd: "******" headers: content_type: "application/json" return_content: yes register: cookie - debug: msg="{{cookie['cookies']['APIC-cookie']}}" - set_fact: token: "{{cookie['cookies']['APIC-cookie']}}" - name: Login to BIG-IP uri: url: https://{{apic_ip}}/appcenter/F5Networks/F5ACIServiceCenter/loginbigip.json method: POST validate_certs: no body: url: "{{big_ip}}" user: "admin" password: "admin" body_format: json headers: DevCookie: "{{token}}" #The body of this request defines the mapping of Pool to EPG #Here we are mapping pool 'web_pool' to EPG 'internalEPG' which belongs to APIC tenant 'TenantDemo' - name: Deploy AS3 dynamic EP mapping uri: url: https://{{apic_ip}}/appcenter/F5Networks/F5ACIServiceCenter/updateas3data.json method: POST validate_certs: no body: url: "{{big_ip}}" partition: "{{partition}}" application: "DemoApp1" json: class: Application template: http serviceMain: class: Service_HTTP virtualAddresses: - 10.168.56.100 pool: web_pool web_pool: class: Pool monitors: - http members: - servicePort: 80 serverAddresses: [] - addressDiscovery: event servicePort: 80 constants: class: Constants serviceCenterEPG: web_pool: tenant: TenantDemo application: AppProfile epg: internalEPG body_format: json status_code: - 202 - 200 headers: DevCookie: "{{token}}" return_content: yes register: complete_info - name: Get task ID of above request set_fact: task_id: "{{ complete_info.json.message.taskId}}" when: complete_info.json.code == 202 - name: Get deployment status uri: url: https://{{apic_ip}}/appcenter/F5Networks/F5ACIServiceCenter/getasynctaskresponse.json method: POST validate_certs: no body: taskId: "{{task_id}}" body_format: json headers: DevCookie: "{{token}}" return_content: yes register: result until: result.json.message.message != "in progress" retries: 5 delay: 2 when: task_id is defined - name: Display final result debug: var: result After deploying this configuration, adding/deleting pool members and making sure the configuration is in sync is the responsibility of the F5 ACI ServiceCenter. Takeaways Both methods are highly effective and usable. The choice of which one to use comes down to the operational model in your environment. Some pros and cons to help made the decision on which platform to use for automation. Ansible Tower Pros No dependency on any other tools Fits in better with bigger company automation strategy to use Ansible for ALL network automation Cons Have to manage playbook execution and scheduling using Ansible Tower If more logic is needed besides what’s described above playbooks will have to be written and maintained Execution of playbook is based on scheduling and is not event driven F5 ACI ServiceCenter Pros Only pool-epg mapping has to be deployed using automation, rest all is handled by the application User interface to view pool member to EPG mapping once deployed and view discrepancies if any Limited automation knowledge is needed, heavy lifting is being done by the application Dynamically adding/deleting pool members is event driven, as members are learned/unlearned by the F5 ACI ServiceCenter an action is taken Cons Another tool is required Customization of pool to EPG mapping is not present. Only one-to-one EPG to pool mapping is present. References Learn about the F5 ACI ServiceCenter and other Cisco integrations: https://f5.com/cisco Download the F5 ACI ServiceCenter: https://dcappcenter.cisco.com/f5-aci-servicecenter.html Lab to execute Ansible playbooks: https://dcloud.cisco.com (Lab name: F5 and Ansible )1.6KViews1like0CommentsWhy is an Active-Active configuration not recommended by F5?
I was considering configuring our F5 LTMs in an Active/Active state within Cisco ACI but I read here that this type of configuration is not recommended without having at least one F5 in standby mode. "F5 does not recommend deploying BIP-IP systems in an Active-Active configuration without a standby device in the cluster, due to potential loss of high availability." Why is this? With two F5s in Active/Active mode, they should still fail over to each other if one happens to go down. Would it take longer for one device to fail over to another who is active rather than being truly standby?1.1KViews0likes5CommentsLoad balancing between an external network and an EPG in ACI.
In all of the documentation I see for setting up a service graph in ACI, it's always between two EPGs. What if the "consumer" or "client" is really going to be external users outside of the fabric that would communicate in via a L3 Out? A L3 Out is not an EPG so how do I load balance between an external network and an EPG?353Views0likes1CommentDNS Load Balancing in Cisco ACI
Hi all, does anyone know of any documentation that exists for DNS Load Balancing within Cisco ACI? I see that it's recommended now to use the iApp wizard for DNS Servers but I'm thinking when I create a Service Graph (Virtual Server) within ACI, I'm not going to be able to use the iApp within the APIC GUI. Does anyone have any prior experience with setting this up? Thanks!421Views0likes2CommentsIntegration question: Cisco ACI with f5 in unmanaged mode
(knowledge level : rudimentary :: first aci <-> f5 integeration project of my life:: reaching out to the community since everyone seems to be baffled) Need help in getting a stalled project through. trying to reach out the community to identify any direct Cisco ACI + f5 technical material to understand and configure f5 in unmanaged mode. There are quite a few links dealing in more complex vcmp/virtual and other issues. The work done so far: expected target architecture : Use f5 in unmanaged mode with ACI. With ACI expected to act like a regular switch and not be bothered with l4-7 et al. f5 configs: single physical f5 device : Port 2.1 and 2.2 : portchanneled to ACI 9K leaf switches : trunk is green/up! When you talk to Cisco as soon as they here f5 - the immediate jump is to configure l4-7. Q: When f5 is treating ACI as a switch how do i configure so that is it not bothered with l4-7 et al. Any discussion around this to further expand will be highly appreciated. Thanks,604Views0likes2Comments