Forum Discussion
Allim_63326
Nimbostratus
NimbostratusCSS Config to F5 Config
I don't know if this is the right section to place this question, if not please direct me to right place.
We have bought 2 F5 3600s, we migrating from old CSS to F5s now. i was wondering if there's tool or any script to convert the exiting CSS configuration file to F5's bigip config file. We are going to use the same ip address from CSS.
Any help would be greatly appreciated.
10 Replies
- dennypayne
Employee
Hi,
What I have found is that there is no single tool that can accurately script a conversion of every possible configuration out there. There are so many variations in network topology, naming conventions, etc. that properly converting all the behavior of previous technologies is difficult.
If you have less than 50 or so virtual servers, you'll be better off doing the conversion by hand. If you have more than that, then a script can save time, but I'd still be prepared to do a fair amount of manual tweaking. I wrote a script to convert ~1600 virtuals from a CSM (not CSS) configuration, and it was highly dependent on known elements of the customer's config to work properly (so it can't be reused for another site), and even then I had to manually redo stuff.
Given enough time, a script could probably be developed to handle generic configs, but again it's usually not worth the effort for typically sized configs.
Denny - JRahm
Admin
I wrote a perl script to do this when I converted my configs a few years back, let me dig for a little while... 
Allim_63326Well thank you so much for your quick response. I will wait for the script, we have close to 100 servers that I need to configure manually If I decide to that route.
Again thank u for the help- JRahmSorry to keep you waiting...I have a thumb drive I can't find and I'm pretty sure it's on there.
- Allim_63326Just wondering if you had any luck to find the script. Appreciate any help
- If someone posts an example of what needs to be converted, I'll see if I can build a little app that will either spit out the bigip.conf configuration or write an iControl app that will create the objects remotely.
-Joe - Allim_63326This is just a small piece of CSS config but the pattern is same
Service
owners
group
!************************** SERVICE **************************
service admin.a1
ip address 10.10.5.11
active
service admin.a2
ip address 10.10.5.12
active
service admin.a3
ip address 10.10.5.13
active
service testadminservice
keepalive retryperiod 20
ip address 10.10.5.14
active
service testadminservice_lb
keepalive retryperiod 20
ip address 10.10.5.15
active
!*************************** OWNER ***************************
owner VZ1
content appsrv1.vz1.va
vip address 10.10.20.11
protocol tcp
port 80
add service appsrv1.vz1.va
active
content appsrv1.vz1.va.1449
protocol tcp
vip address 10.10.20.12
port 1449
add service appsrv1.vz1.va
active
!*************************** GROUP ***************************
group admin_va
vip address 10.10.10.11
active
group adminmliproxy2_va
vip address 10.10.10.12
active
group ftp
vip address 10.10.10.13
add service ftp1.a1.va
active - Allim_63326Hi Joe, Any luck
- Guys
Sorry I am late to this. I wrote a CSS config conversion script in Perl. Contact me if you need it. j.alam@f5.com
The script is pretty extensive I could not attach it to this Post.
I will try posting it elsewhere on devcentral.
John - JRahmIt is now available in the wiki. Thanks John!
http://devcentral.f5.com/wiki/default.aspx/AdvDesignConfig/CSSToBIGIPConversionScript.html Click here
