Implementing SSL Orchestrator - High Level Considerations
Introduction This article is the beginning of a multi-part series on implementing BIG-IP SSL Orchestrator. It includes high availability and central management with BIG-IQ. Implementing SSL/TLS Decryption is not a trivial task. There are many factors to keep in mind and account for, from the network topology and insertion point, to SSL/TLS keyrings, certificates, ciphersuites and on and on. This article focuses on pre-deployment tasks and preparations for SSL Orchestrator. This article is divided into the following high level sections: Solution Overview Customer Use Case Architecture & Network Topology Please forgive me for using SSL and TLS interchangeably in this article. Software versions used in this article: BIG-IP Version: 14.1.2 SSL Orchestrator Version: 5.5 BIG-IQ Version: 7.0.1 Solution Overview Data transiting between clients (PCs, tablets, phones etc.) and servers is predominantly encrypted with Secure Socket Layer (SSL) and its evolution Transport Layer Security (TLS)(ref. Google Transparency Report). Pervasive encryption means that threats are now predominantly hidden and invisible to security inspection unless traffic is decrypted.The decryption and encryption of data by different devices performing security functions potentially adds overhead and latency.The picture below shows a traditional chaining of security inspection devices such as a filtering web gateway, a data loss prevention (DLP) tool, and intrusion detection system (IDS) and next generation firewall (NGFW). Also, TLS/SSL operations are computationally intensive and stress the security devices’ resources.This leads to a sub-optimal usage of resource where compute time is used to encrypt/decrypt and not inspect. F5’s BIG-IP SSL Orchestrator offers a solution to optimize resource utilization, remove latency, and add resilience to the security inspection infrastructure. F5 SSL Orchestrator ensures encrypted traffic can be decrypted, inspected by security controls, then re-encrypted—delivering enhanced visibility to mitigate threats traversing the network. As a result, you can maximize your security services investment for malware, data loss prevention (DLP), ransomware, and next-generation firewalls (NGFW), thereby preventing inbound and outbound threats, including exploitation, callback, and data exfiltration. The SSL Orchestrator decrypts the traffic and forwards unencrypted traffic to the different security devices for inspection leveraging its optimized and hardware-accelerated SSL/TLS stack.As shown below the BIG-IP SSL Orchestrator classifies traffic and selectively decrypts traffic.It then forwards it to the appropriate security functions for inspection.Finally, once duly inspected the traffic is encrypted and sent on its way to the resource the client is accessing. Deploying F5 and inline security tools together has the following benefits: Traffic Distribution for load sharing Improve the scalability of inline security by distributing the traffic across multiple Security appliances, allowing them to share the load and inspect more traffic. Agile Deployment Add, remove, and/or upgrade Security appliances without disrupting network traffic; converting Security appliances from out-of-band monitoring to inline inspection on the fly without rewiring. Customer Use Case This document focuses on the implementation of BIG-IP SSL Orchestrator to process SSL/TLS encrypted traffic and forward it to a security inspection/enforcement devices. The decryption and forwarding behavior are determined by the security policy. This ensures that only targeted traffic is decrypted in compliance with corporate and regulator policy, data privacy requirements, and other relevant factors. The configuration supports encrypted traffic that originates from within the data center or the corporate network.It also supports traffic originating from clients outside of the security perimeter accessing resources inside the corporate network or demilitarized zone (DMZ) as depicted below. The decrypted traffic transits through different inspection devices for inbound and outbound traffic. As an example, inbound traffic is decrypted and processed by F5’s Advanced Web Application Firewall (F5 Advanced WAF) as shown below. *Can be encrypted or cleartext as needed As an example, outbound traffic is decrypted and sent to a next generation firewall (NGFW) for inspection as shown in the diagram below. The BIG-IP SSL Orchestrator solution offers 5 different configuration templates. The following topologies are discussed in Network Insertion Use Cases. L2 Outbound L2 Inbound L3 Outbound L3 Inbound L3 Explicit Proxy Existing Application In the use case described herein, the BIG-IP is inserted as layer 3 (L3) network device and is configured with an L3 Outbound Topology. Architecture & Network Topology The assumption is that, prior to the insertion of BIG-IP SSL Orchestrator into the network (in a brownfield environment), the network looks like the one depicted below.It is understood that actual networks will vary, that IP addressing, L2 and L3 connectivity will differ, however, this is deemed to be a representative setup. Note: All IP addressing in this document is provided as examples only.Private IP addressing (RFC 1918) is used as in most corporate environments. Note: the management network is not depicted in the picture above.Further discussion about management and visibility is the subject of Centralized Management below. The following is a description of the different reference points shown in the diagram above. a.This is the connection of the border routers that connect to the internet and other WAN and private links. Typically, private IP addressing space is used from the border routers to the firewalls. b.The border switching connects to the corporate/infrastructure firewall.Resilience is built into this switching layer by implementing 2 link aggregates (LAG or Port Channel ®). c.The “demilitarized zone”(DMZ) switches are connected to the firewall.The DMZ network hosts application that are accessible from untrusted networks such as the Internet. d.Application server connect into the DMZ switch fabric. e.Firewalls connect into the switch fabric.Typically core and distribution infrastructure switching will provide L2 and L3 switching to the enterprise (in some case there may be additional L3 routing for larger enterprises/entities that require dynamic routing and other advanced L3 services. f.The connection between the core and distribution layers are represented by a bus on the figure above because the actual connection schema is too intricate to picture.The writer has taken the liberty of drawing a simplified representation.Switches actually interconnect with a mixture of link aggregation and provide differentiated switching using virtualization (e.g. VLAN tagging, 802.1q), and possibly further frame/packet encapsulation (e.g. QinQ, VxLAN). g.The core and distribution switching are used to create 2 broadcast domains. One is the client network, and the other is the internal application network. h.The internal applications are connected to their own subnet. The BIG-IP SSL Orchestrator solution is implemented as depicted below. In the diagram above, new network connections are depicted in orange (vs. blue for existing connections).Similarly to the diagram showing the original network, the switching for the DMZ is depicted using a bus representation to keep the diagram simple. The following discusses the different reference points in the diagram above: a.The BIG-IP SSL Orchestrator is connected to the core switching infrastructure A new VLAN and network are created on the core switching infrastructure to connect to the firewalls (North) to the BIG-IP SSL Orchestrator devices. b.The client network (South) is connected to the BIG-IP via a second VLAN and network. c.The SSL Orchestrator devices are connected to a newly created inspection network.This network is kept separate from the rest of the infrastructure as client traffic transits through the inspection devices unencrypted.As an example, Web Application Firewalls (BIG-IP ASM) are used to filter inbound traffic. d. The LAN configuration for the connection to the BIG-IP ASM is as depicted below. e. The NGFW is connected to the INSPECTION switching network in such a manner that traffic traverses it when the BIG-IP SSL Orchestrator is configured to push traffic for inspection. Summary This article should be a good starting point for planning your initial SSL Orchestrator deployment. We covered the solution overview and use cases. The network topology and architecture was explained with the help of diagrams. Next Steps Click Next to proceed to the next article in the seriesImplementing SSL Orchestrator - L2 Service Configuration (Palo Alto)
Introduction This article is part of a series on implementing BIG-IP SSL Orchestrator. It includes high availability and central management with BIG-IQ. Implementing SSL/TLS Decryption is not a trivial task. There are many factors to keep in mind and account for, from the network topology and insertion point, to SSL/TLS keyrings, certificates, ciphersuites and on and on. This article focuses on configuring a 3rd party, inline Layer 2 security device and everything you need to know about it. This article covers the configuration of a Palo Alto NGFW running PAN-OS version 9.0.3. Please forgive me for using SSL and TLS interchangeably in this article. The simplest Palo Alto deployment is in Layer 2, or Virtual Wire mode.This combines 2 interfaces to act as an L2 bridge where data flows into one interface and is passed out the other interface. From the Palo Alto UI go to the Network tab > Interfaces. Click the name (ethernet1/X) of the interface you wish to configure. Set the Interface Type to Virtual Wire and the Security Zone to trust.Click OK. Do the same for the next interface. Click the name of one of the interfaces configured previously.Click Virtual Wire > New Virtual Wire. Give it a name.Select the 2 interfaces configured previously.Click OK and OK. You will need to Commit the changes for them to take effect. Note: setting the Security Zone to trust is needed for the F5 Health Monitors to work. Summary In this article you learned how to configure a Palo Alto NGFW in Layer 2 mode. Configuration of Palo Alto NGFW can be downloaded fromherefrom GitLab. Next Steps Contact Palo Alto Networks if you need additional assistance with their products. Click Next to proceed to the next article in the series.Implementing SSL Orchestrator - L3 Mode Deployment
Introduction This article shows you how to deploy SSL Orchestrator in Layer 3 (L3) mode This article is divided into the following high level sections: Network Topology Requirements Best Practices Known Limitations Please forgive me for using SSL and TLS interchangeably in this article. Software versions used in this article: BIG-IP Version: 14.1.2 SSL Orchestrator Version: 5.5 BIG-IQ Version: 7.0.1 Network Topology The diagram below is a representation of the actual lab network where SSL Orchestrator was deployed and tested. Before SSL Orchestrator After SSL Orchestrator All routing configuration is static routing – no dynamic routing protocols is implemented in this design.Dynamic Routing was not considered for this article series. The design allows for the administrator to gradually forward services to the BIG-IP SSL Orchestrator using source-based routing rules.The end-result is to have all outbound and inbound traffic traversing the BIG-IP SSL Orchestrator solution. Requirements BIG-IP Version: 14.1.2 SSL Orchestrator Version: 5.5 BIG-IQ Version: 7.0.1 NGWF Version: Details are beyond the scope of this discussion – note that NGWF is configured with a "Virtual Wire" and performs its inspection as a transparent L2 device. Adv. WAF: Details are beyond the scope of this discussion – for this implementation, the Advanced WAF module is running on a separate BIG-IP platform. Configuration of BIG-IP deployed as SSL Orchestrator can be downloaded fromherefrom GitLab. Demo videos are available for both Inbound and Outbound use cases: Outbound Traffic Inspection Inbound Traffic Inspection Best Practices for SSL Orchestrator Deployment BIG-IP Recommendations The following provides salient recommendations, these and others are discussed in detail in theSSL Orchestrator Document. AutoMap AutoMap is a secure network address translation (SNAT) described in Knowledge articleK7336. AutoMap should not be used where possible in BIG-IP SSL Orchestrator deployments. Please refer toK7820for SNAT uses and best practices.With BIG-IP configurations (SSLO or other modules), whenever a large number of connections are going to require SNAT, you want to make sure that SNAT pools are used to avoid port collisions (running out of ephemeral ports to initiate the connection). Debug Logging Traffic through BIG-IP SSL Orchestrator will transit through different services as defined in the service chain.Enabling debug will generate logs as traffic traverses the different services – this can be very verbose and generate large amounts of traffic. It is recommended to leverage debug logging for troubleshooting only. Security Recommendations The following recommendations can also be found in theSSL Orchestrator Document. SSL Orchestrator and Service Proximity SSL Orchestrator is almost never first in an enterprise architecture, so other security devices (proxies, firewalls, IPSs, sandboxes, etc.) are already deployed. If you ask any network and/or security admin, 99% of the time they have no interest in moving those security devices or re-architecting anything else when SSL Orchestrator is introduced. However, remember that the traffic being sent to and from the security devices is unencrypted, so sending traffic across an existing enterprise network to some security device is also sending passwords, credit card numbers, and other protected data (HIPAA, PCI, etc.), across an uncontrolled span of network where any connected device can see it in clear text. It is therefore brutally important that customers understand this, and that they do move those security devices to networks that are behind and protected by SSL Orchestrator. In a perfect situation, no traffic should be able to reach these security devices except through SSL Orchestrator. As frightening as the possibility of a data exposure is, there are going to be customers that ignore the warnings. You should therefore do your best to convey this security best practice to customers as their trusted advisor. This is the reason for the “Auto-Manage” field in the configuration for the services. It creates non- overlapping, internal, non-routable address spaces for each service and encourages customers to protect them. If disabling this, and changing the inline service IP spaces, take care to protect these. Known Limitations It is recommended to consult with the Knowledge ArticleK00805840for current known issues and workarounds. Strictness Underlying the BIG-IP SSL Orchestrator is the BIG-IP TMOS infrastructure.The BIG-IP SSL Orchestrator provides a guided configuration front-end to configure TMOS to build the services, and different policies to make the solution work as designed. If the administrator were to dive deeper in the low-level configuration of the device after building a topology, the configuration would contain BIG-IPconfiguration items – refer to Appendix C for sample configuration for a simple SSL Orchestrator configuration. The notion of strictness is introduced to “lock” the configured items in such a manner as to prevent the administrator to be able to modify the underlying object without using the SSL Orchestrator interface. Any attempt to modify an object that is strictly managed will result in an error message as shown below: Gossip For BIG-IP SSL Orchestrator deployed in redundant pairs, BIG-IP should be in manual/full sync mode (Device Management>>Device Group).For more information related to BIG-IP high availability (HA) configuration, refer to theuser guide. The traditional synchronization mechanism is augmented with “gossip” for the SSL Orchestrator.This synchronization mechanism is independent from typical LTM config sync.For the version of BIG-IP SSL Orchestrator used for this deployment, ”gossip” config sync is two-way automatic."gossip" uses REST API calls for the SSL Orchestrator related part of the config sync.If a change is made to one device in the pair, it is automatically propagated to the other device.This differs from the traditional BIG-IP sync behavior. SSL Orchestrator config needs to be re-deployed if a STANDALONE environment is changed to an HA environment. Also, you need to make sure VLAN configuration is the same on both the box for successful re-deployment. Summary This article should be a good starting point for planning your initial SSL Orchestrator deployment. The network topology and architecture was explained with the help of diagrams. We also went over the software requirements, best practices and known limitations. Next Steps Click Next to proceed to the next article in the series.
SSLO routing error
Hi guys, Whenever I try to run the SSLO with the services I always get the request back from my servers but if I add the services in the service chain it's not pushing thru. The devices are reachable with the corresponding interfaces, but I really can't seem to route and inspect the traffic from the services. Any ideas on how to fix this? Are there particular configurations that should be made first with my IPS to route the incoming traffic to the outgoing interface? I'm really lost on this one.
