IP::addr and IPv6
Did you know that all address internal to tmm are kept in IPv6 format? If you’ve written external monitors, I’m guessing you knew this. In the external monitors, for IPv4 networks the IPv6 “header” is removed with the line: IP=`echo $1 | sed 's/::ffff://'` IPv4 address are stored in what’s called “IPv4-mapped” format. An IPv4-mapped address has its first 80 bits set to zero and the next 16 set to one, followed by the 32 bits of the IPv4 address. The prefix looks like this: 0000:0000:0000:0000:0000:ffff: (abbreviated as ::ffff:, which looks strickingly simliar—ok, identical—to the pattern stripped above) Notation of the IPv4 section of the IPv4-formatted address vary in implementations between ::ffff:192.168.1.1 and ::ffff:c0a8:c8c8, but only the latter notation (in hex) is supported. If you need the decimal version, you can extract it like so: % puts $x ::ffff:c0a8:c8c8 % if { [string range $x 0 6] == "::ffff:" } { scan [string range $x 7 end] "%2x%2x:%2x%2x" ip1 ip2 ip3 ip4 set ipv4addr "$ip1.$ip2.$ip3.$ip4" } 192.168.200.200 Address Comparisons The text format is not what controls whether the IP::addr command (nor the class command) does an IPv4 or IPv6 comparison. Whether or not the IP address is IPv4-mapped is what controls the comparison. The text format merely controls how the text is then translated into the internal IPv6 format (ie: whether it becomes a IPv4-mapped address or not). Normally, this is not an issue, however, if you are trying to compare an IPv6 address against an IPv4 address, then you really need to understand this mapping business. Also, it is not recommended to use 0.0.0.0/0.0.0.0 for testing whether something is IPv4 versus IPv6 as that is not really valid a IP address—using the 0.0.0.0 mask (technically the same as /0) is a loophole and ultimately, what you are doing is loading the equivalent form of a IPv4-mapped mask. Rather, you should just use the following to test whether it is an IPv4-mapped address: if { [IP::addr $IP1 equals ::ffff:0000:0000/96] } { log local0. “Yep, that’s an IPv4 address” } These notes are covered in the IP::addr wiki entry. Any updates to the command and/or supporting notes will exist there, so keep the links handy. Related Articles F5 Friday: 'IPv4 and IPv6 Can Coexist' or 'How to eat your cake ... Service Provider Series: Managing the ipv6 Migration IPv6 and the End of the World No More IPv4. You do have your IPv6 plan running now, right ... Question about IPv6 - BIGIP - DevCentral - F5 DevCentral ... Insert IPv6 address into header - DevCentral - F5 DevCentral ... Business Case for IPv6 - DevCentral - F5 DevCentral > Community ... We're sorry. The IPv4 address you are trying to reach has been ... Don MacVittie - F5 BIG-IP IPv6 Gateway ModuleBIG-IP Configuration Conversion Scripts
Kirk Bauer, John Alam, and Pete White created a handful of perl and/or python scripts aimed at easing your migration from some of the “other guys” to BIG-IP.While they aren’t going to map every nook and cranny of the configurations to a BIG-IP feature, they will get you well along the way, taking out as much of the human error element as possible.Links to the codeshare articles below. Cisco ACE (perl) Cisco ACE via tmsh (perl) Cisco ACE (python) Cisco CSS (perl) Cisco CSS via tmsh (perl) Cisco CSM (perl) Citrix Netscaler (perl) Radware via tmsh (perl) Radware (python)
20 Lines or Less #1
Yesterday I got an idea for what I think will be a cool new series that I wanted to bring to the community via my blog. I call it "20 lines or less". My thought is to pose a simple question: "What can you do via an iRule in 20 lines or less?". Each week I'll find some cool examples of iRules doing fun things in less than 21 lines of code, not counting white spaces or comments, round them up, and post them here. Not only will this give the community lots of cool examples of what iRules can do with relative ease, but I'm hoping it will continue to show just how flexible and light-weight this technology is - not to mention just plain cool. I invite you to follow along, learn what you can and please, if you have suggestions, contributions, or feedback of any kind, don't hesitate to comment, email, IM, whatever. You know how to get a hold of me...please do. ;) I'd love to have a member contributed version of this once a month or quarter or ... whatever if you guys start feeding me your cool, short iRules. Ok, so without further adieu, here we go. The inaugural edition of 20 Lines or Less. For this first edition I wanted to highlight some of the things that have already been contributed by the awesome community here at DevCentral. So I pulled up the Code Share and started reading. I was quite happy to see that I couldn't even get halfway through the list of awesome iRule contributions before I found 5 entries that were neat, and under 20 lines (These are actually almost all under 10 lines of code - wow!) Kudos to the contributors. I'll grab another bunch next week to keep highlighting what we've got already! Cipher Strength Pool Selection Ever want to check the type of encryption your users are using before allowing them into your most secure content? Here's your solution. when HTTP_REQUEST { log local0. "[IP::remote_addr]: SSL cipher strength is [SSL::cipher bits]" if { [SSL::cipher bits] < 128 }{ pool weak_encryption_pool } else { pool strong_encryption_pool } } Clone Pool Based On URI Need to clone some of your traffic to a second pool, based on the incoming URI? Here you go... when HTTP_REQUEST { if { [HTTP::uri] starts_with "/clone_me" } { pool real_pool clone pool clone_pool } else { pool real_pool } } Cache No POST Have you been looking for a way to avoid sending those POST responses to your RAMCache module? You're welcome. when HTTP_REQUEST { if { [HTTP::method] equals "POST" } { CACHE::disable } else { CACHE::enable } } Access Control Based on IP Here's a great example of blocking unwelcome IP addresses from accessing your network and only allowing those Client-IPs that you have deemed trusted. when CLIENT_ACCEPTED { if { [matchclass [IP::client_addr] equals $::trustedAddresses] }{ #Uncomment the line below to turn on logging. #log local0. "Valid client IP: [IP::client_addr] - forwarding traffic" forward } else { #Uncomment the line below to turn on logging. #log local0. "Invalid client IP: [IP::client_addr] - discarding" discard } } Content Type Tracking If you're looking to keep track of the different types of content you're serving, this iRule can help in a big way. # First, create statistics profile named "ContentType" with following entries: # HTML # Images # Scripts # Documents # Stylesheets # Other # Now associate this Statistics Profile to the virtual server. Then apply the following iRule. # To view the results, go to Statistics -> Profiles - Statistics when HTTP_RESPONSE { switch -glob [HTTP::header "Content-type"] { image/* { STATS::incr "ContentType" "Images" } text/html { STATS::incr "ContentType" "HTML" } text/css { STATS::incr "ContentType" "Stylesheets" } *javascript { STATS::incr "ContentType" "Scripts" } text/vbscript { STATS::incr "ContentType" "Scripts" } application/pdf { STATS::incr "ContentType" "Documents" } application/msword { STATS::incr "ContentType" "Documents" } application/*powerpoint { STATS::incr "ContentType" "Documents" } application/*excel { STATS::incr "ContentType" "Documents" } default { STATS::incr "ContentType" "Other" } } } There you have it, the first edition of "20 Lines or Less"! I hope you enjoyed it...I sure did. If you've got feedback or examples to be featured in future editions, let me know. #Colin
