Bigpipe Mappings

Problem this snippet solves:

Have questions about transitioning from bigpipe to tmsh? Here are some helpful hints. For full documentation see the tmsh Reference Guide on AskF5 .

Important things to remember when examining commands in tmsh:

show (usually) provides just the statistical information, with configuration parameters present to provide a level of disambiguation.
list provides configuration information, but just variations from the default. For example, “list /ltm nat 192.0.2.1” will only show the “originating-address” information
all-properties extends a “list” command to show every configuration option, not just the variations from default.

bigpipe command	tmsh Command	Comment
b arp show	show /net arp all
b arp all delete	tmsh delete /net arp all
b class DATA-GROUP mode read	modify ltm data-group DATA-GROUP access-mode read-only
b class show	show running-config /ltm data-group
b cluster show	show /sys cluster all-properties
b config save file.ucs	save /sys ucs file.ucs
b config install file.ucs	load /sys ucs file.ucs
b config sync	run /sys config-sync	For v10 config-sync only, where "pull" is optional
b config sync	run /cm config-sync from-group/to-group DEVICEGROUPNAME	For v11 traffic-group config-sync only
b conn show	show /sys connection
b conn show all	show /sys connection all-properties	Show all connection table properties
b conn ss server node-ip:node-port delete	delete /sys connection ss-server-addr node-ip ss-server-port node-port	Delete connection table entries for node-ip node-port
b daemon list	list /sys daemon-ha all-properties
b db < key name > < value >	modify /sys db < key name > value < value >	Modify database values
b db Platform.PowerSupplyMonitor disable	tmsh modify sys db platform.powersupplymonitor value disable	Disables PSU alert if only one PSU in use on Dual PSU system
b db show	show running-config /sys db -hidden all-properties
b export my.config.scf	save /sys scf my.config.scf	v10.x only
b export my.config.scf	save /sys config file my.config.scf tar-file my.config.tar	v11.0+
b fo show	run /util bigpipe fo	v10+
b fo show	show /sys failover	v11+
b fo offline	run /sys failover offline	v11+ force the unit offline
b fo online	run /sys failover online	v11+ release offline to go either standby or active
b fo standby	run /util bigpipe fo standby	v10+
b fo standby	run /sys failover standby	v11+
b ha table	show /sys ha-status all-properties
b ha group	show /sys ha-group detail
b hardware baud rate	modify /sys console baud-rate	v10: sol10621 \| v11: sol13325
b system console inactivity timeout #	tmsh modify sys global-settings console-inactivity-timeout #	Set Serial Console Idle Timeout - replace # with seconds until timeout or "show" to see current timeout setting
b ha table show	show /sys ha-status all-properties
b httpd list	list /sys httpd	To list httpd configuration.
b import my.config.scf	load /sys scf my.config.scf	v10.x only
b import my.config.scf	load /sys config file my.config.scf tar-file my.config.tar	v11.0+
b interface show -j	show /net interface -hidden all-properties	-hidden is not tab completable, but should be shown in the command output on iHealth.
b load	load sys config partitions all
b merge	load /sys config merge	Added in v11. In v10 use bigpipe
b merge /path/to/file.txt	tmsh load /sys config file /path/to/file.txt merge	Merge a file into the BIG-IP configuration. Added in v11. In v10, use bigpipe
b mgmt show	show running-config /sys management-ip
b mgmt route any gateway 192.168.0.1	tmsh create /sys management-route default gateway 192.168.0.1
b monitor show	show running-config /ltm monitor (?)
b nat show	show /ltm nat all or list /ltm nat all-properties	The two tmsh commands are required here since b nat show will list the unit preference and ARP status. Statistical information is shown via "show" while configuration information is shown via "list".
b node all monitor show	list ltm node monitor
b node show	show /ltm node
b ntp servers 10.10.10.10	modify sys ntp servers add { 10.10.10.10 }
b packet filter all show	show /net packet-filter
b partition	list auth partition	no "show" command yet, list will only show written partitions
b persist	tmsh show ltm persistence persist-records
b platform	show /sys hardware
b pool list	list /ltm pool
b pool mypool member 192.168.0.1:80 add	tmsh modify /ltm pool mypool members add { 192.168.0.1:80 }
b pool mypool member 10.10.10.10:80 down	(v10.2.4) tmsh modify ltm pool webbian443 members modify { 192.168.10.16:https { state down } } \| (v11.1) tmsh modify ltm pool httppool1 members modify { 10.10.10.10:80 { state user-down } }
b pool show	show /ltm pool members
b profile access all stats
b profile auth all show all	show /ltm auth profile all	The tmsh auth command does not display associated OCSP information shown by bigpipe.
b profile http ramcache show	show /ltm profile http
b profile http stats	show /ltm profile http
b profile ssl stats	show /ltm profile ssl
b profile persist profile_name list all	tmsh list ltm persistence profile_name all-properties
b profile tcp show	show /ltm profile tcp
b profile tcp stats	show /ltm profile tcp
b profile udp show	show /ltm profile udp
b profile udp stats	show /ltm profile udp
b profile xml show	show /ltm profile xml
b reset	load / sys default-config	v10.x
b reset	load / sys config default	v11.x
b route show	show /net route all
b rule < rule > show all	show /ltm rule < rule >
b rule show	show /ltm rule all
b rule stats reset	reset-stats /ltm rule < rule >
b save	save sys config partitions all
b self show	show running-config /net self
b snat	show /ltm snat
b snatpool show	show /ltm snatpool
b software	show sys software
b software desired	install sys software image NAME volume HDX.Y reboot
b software desired	install sys software image NAME create-volume volume HDX.Y	v11.0+ : Creates volume and installs software. (Cannot create empty volumes in v11)
b software desired	install sys software hotfix NAME volume HDX.Y	Installs desired Hotfix to the specified Volume.
b stp show	show running-config /net stp all-properties
b syslog list all	list sys syslog all-properties
b syslog remote server none	modify sys syslog remote-servers none
b syslog remote server test-srv host 192.168.206.47	modify sys syslog remote-servers add {test-srv{host 192.168.206.47}}	You can append "remote-port 517" for example to the end of the command to specify the port
b syslog remote server test-srv local ip 172.28.72.90	modify sys syslog remote-servers modify {test-srv{local-ip 172.28.72.90}}	The self ip must be non-floating
b system hostname	modify sys global-settings hostname NEWHOST.EXAMPLE.COM
b trunk show -j	show /net trunk -hidden all
b trunk all lacp show	show /net trunk detail
b unit show
b verify load	load sys config verify
b version	show /sys version	Takes grep (but not "head" as in "b version \|head") - for example, grep on build: tmsh show sys version \|grep -i build
b virtual address show	show /ltm virtual-address all-properties	"show" does not show the objects used by the virtual, and list does not show statistics.
b virtual all show all	show /ltm virtual all-properties or list /ltm virtual all-properties	"show" does not show the objects used by the virtual, and list does not show statistics.
b vlan all show all -j	show /net vlan -hidden
b vlangroup all show all	show /net vlan-group all
bigstart status\|start\|stop\|restart SERVICE_NAME	show\|start\|stop\|restart sys service SERVICE_NAME
bpsh (?)	load sys config from-terminal merge	Merge config from interactive shell. Paste/type the config objects you want to add. Then type Ctrl+d to complete the submission or Ctrl+c to cancel the input. Added in v11.0.

Linux Commands (Commands only accessible from the CLI)

Linux Command	tmsh	Comment
arp -an	run /util bash -c "arp -an"
crontab -l	run /util bash -c "crontab -l"
date	run /util bash -c "date"
df -h	run /util bash -c "df -h"
df -i	run /util bash -c "df -i"
df -ik	run /util bash -c "df -ik"
eud_info (version)	run /util bash -c "eud_info (version)"
free	run /util bash -c "free"
grub default -d	run /util bash -c "grub default -d"
grub default -l	run /util bash -c "grub default -l"
halid	run /util bash -c "halid"
hsb snapshot (version)	run /util bash -c "hsb snapshot (version)"
ifconfig -a	run /util bash -c "ifconfig -a"
interrupts	run /util bash -c "interrupts"
ip -f dnet addr show	run /util bash -c "ip -f dnet addr show"
ip -f inet addr show	run /util bash -c "ip -f inet addr show"
ip -f inet link show	run /util bash -c "ip -f inet link show"
ip -f inet neigh show	run /util bash -c "ip -f inet neigh show"
ip -f inet route show	run /util bash -c "ip -f inet route show"
ip -f inet rule show	run /util bash -c "ip -f inet rule show"
ip -f inet tunnel show	run /util bash -c "ip -f inet tunnel show"
ip -f inet6 addr show	run /util bash -c "ip -f inet6 addr show"
ip -f inet6 link show	run /util bash -c "ip -f inet6 link show"
ip -f inet6 neigh show	run /util bash -c "ip -f inet6 neigh show"
ip -f inet6 route show	run /util bash -c "ip -f inet6 route show"
ip -f inet6 tunnel show	run /util bash -c "ip -f inet6 tunnel show"
ip -f ipx addr show	run /util bash -c "ip -f ipx addr show"
ip -f link addr show	run /util bash -c "ip -f link addr show"
ip -f link link show	run /util bash -c "ip -f link link show"
ip -f link neigh show	run /util bash -c "ip -f link neigh show"
ip -f link route show	run /util bash -c "ip -f link route show"
ls -las /var/local/ucs	run /util bash -c "ls -las /var/local/ucs"
ls -lasLR /dev/mprov/	run /util bash -c "ls -lasLR /dev/mprov/"
ls -lasLR /var/core	run /util bash -c "ls -lasLR /var/core"
ls -lasR /boot	run /util bash -c "ls -lasR /boot"
ls -lasR /hotfix	run /util bash -c "ls -lasR /hotfix"
lsof -n	run /util bash -c "lsof -n"
meminfo	run /util bash -c "meminfo"
mount	run /util bash -c "mount"
netstat -nge	run /util bash -c "netstat -nge"
netstat -ni	run /util bash -c "netstat -ni"
netstat -pan	run /util bash -c "netstat -pan"
netstat -sa	run /util bash -c "netstat -sa"
ntpdc -n -c peer 127.0.0.1	run /util bash -c "ntpdc -n -c peer 127.0.0.1"
ntpq -pn	run /util bash -c "ntpq -pn"
pci	run /util bash -c "pci"
pstree	run /util bash -c "pstree"
qkview	run /util qkview
rpm -qa	run /util bash -c "rpm -qa"
switchboot -l	run /util bash -c "switchboot -l"	Or use: /sys reboot volume < volume >
sysctl	run /util bash -c "sysctl"
top	run /util bash -c "top"
vmstat	run /util bash -c "vmstat"
who -aH	run /util bash -c "who -aH"