APM: Why can't get the session.user.sessionid in the ACCESS_ACL_ALLOWED?
Hi Friends Why can't get the session.user.sessionid in the ACCESS_ACL_ALLOWED? Thanks My iRules: Codewhen ACCESS_POLICY_COMPLETED { set hsl [HSL::open -proto UDP -pool pool_172.16.0.21_syslog] set mysession "session_id=[ACCESS::session data get session.user.sessionid]" set timestamp [clock format [clock seconds] -format "%d/%h/%Y:%T %Z" -gmt 1 ] log local0. "access policy completed get session id" } when ACCESS_ACL_ALLOWED { HSL::send $hsl "<190> $timestamp $mysession \n" log local0. "access policy acl allowed" }`text`
System authentication logging
Hi, for some SIEM scenarios I need to have the BigIP login events within our remote log management. Within the GUI I can see the following event if an login failed: Fri Aug 23 09:51:59 CEST 2019 USERNAME 0-0 httpd(pam_audit): User=USERNAME tty=(unknown) host=192.168.178.2 failed to login after 1 attempts (start="Fri Aug 23 09:51:57 2019" end="Fri Aug 23 09:51:59 2019").: For remote logging I've configured the log destination, publisher and a filter. The log destination based on HSL. Within the filter I've severity "information" and source "all". The problem is that the authentication events will not be sended to the remote syslog. All other messages will be sended. If I activate the "remote logging" feature where I receive all messages and where I don`t have any possibility to change the stuff which will be sended I`ll receive the log message regarding successfully and failed logon. Is it possible to receive the authentication events also with only the usage of HSL!? The logs are available at /var/log/secure and /var/log/audit, but they will not be transferred to the remote syslog. I`ve already tested around with some different settings. Within the options for logging I've enabled the audit (tmm / mcp) logging. Any Ideas!? Within the documentation I can only find some informations that the authentication logs are available within /var/log/secure and/or /var/log/audit, but there are no informations how to transfer them. Thanks and Regards seilemor
High-Speed Logging Mgmt Interface
I am trying to setup high-speed remote logging on my Big-IP ASM v12.1.1. I have gone through the f5 documents setting up the server pool, then log destination/publisher/filter, but am not getting any logs. I just read on a post that high-speed logs won't be sent over the mgmt interface. Is that true? Will i need to setup another interface (with static routes?) just for the high-speed logging?BigIP version 10 and logs to remote syslog server
Hi Guys, I have a bigip 3600 version 10 running. I configure the below command to send syslog to a remote serfer, yet I am not geting the logs on the syslog server. Checking the traffic on the network shows that the bigip is not sending syslog traffic. modify /sys syslog remote-servers add { SIEM { host 10.2.160.34 remote-port 514 }}
WHICH VIRTUAL SERVER IS APPLIED TO AN INTERMEDIATE IRULE FOR HIGH SPEED LOGGING.
I would like to ask which virtual server, will be applied to an intermediate irule. The irule listed on Devcentral for high speed logging on f5 to arcsight or splunk on the following devcentral article https://devcentral.f5.com/articles/irules-high-speed-logging-spray-those-log-statements is ltm rule testrule { when CLIENT_ACCEPTED { set lpAll [HSL::open -publisher /Common/lpAll] } when HTTP_REQUEST { HSL::send $lpAll "<190> [IP::client_addr]:[TCP::client_port]-[IP::local_addr]:[TCP::local_port]; [HTTP::host][HTTP::uri]" } } However,i'll like to know which virtual server,the irule will be attached to. Thanks
High Speed Logging - Not working quite as expected (Specific to ArcSight)
Introduction I'm wondering if anyone can offer any advice on how this should be working and whether I'm getting the wrong understanding of this. To be clear, it is not the iRule HSL implementations but simply the built in /sys log-config filters/publishers/destinations. My Requirements I require logs to continue to be available on the Big-IP, as though we've not configured any differences to logging. I also want to log everything (debug from all sources) out to our chosen SIEM product ArcSight. Things to Know I'm using Big-IP 11.6.0 HF3 (ENG) Resources provisioned: APM Not requiring additional logging such as request logging. https://support.f5.com/kb/en-us/products/big-ip_ltm/manuals/product/tmos-implementations-11-6-0/22.html?sr=43624187 Configuration, so far Configured a pool named SIEM-ArcSight-Logging which contains the ArcSight Server, port 514. Configured a destination SIEM-Dest-HSL, type Remote High Speed Logging (unformatted), forwards to SIEM-ArcSight-Logging pool, type UDP Configured a destination SIEM-Dest-ArcSight, type ArcSight (formatted), forwards to SIEM-Dest-HSL Configured a publisher SIEM-Pub-Default, destinations: SIEM-Dest-ArcSight SIEM-Dest-HSL alertd Configured a filter SIEM-Filter, severity Debug, source all, Publisher SIEM-Pub-Default Please note... My gut feeling says I may have set the publisher up wrong, so I have tried each of their entries just on their own. alertd, SIEM-Dest-HSL seem to work fine (I see syslog traffic leaving for the HSL) but ArcSight does not. Documentation seems somewhat unclear as to what destinations are required, i.e. do I just need to add ArcSight and let it forward itself to HSL or do I need both. Also, should I be configuring multiple filters to cover debug/all or am I correct to have just the one 'catch all'. **I have additionally seen a warning on one presentation I bumped into whilst Googling away which said "Warning, dangerous defaults 'debug/all'" but I couldn't find an explanation of why these are dangerous, so I proceeded with caution and tried upping the severity but it made no difference. Any and all feedback/advice/other would be incredibly welcomed. Many thanks, JD.