Hi Friends,
Would like to know if we have the possibility of doing “extended” ping in LTM command line. This is similar to what we do in a router if we want to ping a destination IP from a specific source IP that we want. Thanks,
Srini
Hi Friends,
Would like to know if we have the possibility of doing “extended” ping in LTM command line. This is similar to what we do in a router if we want to ping a destination IP from a specific source IP that we want. Thanks,
Srini
This is similar to what we do in a router if we want to ping a destination IP from a specific source IP that we want.is source ip selfip? if yes, have you tried ping -I option? but if not (selfip), i am not aware of.
e.g.
external vlan is in 172.28.20.0/24 subnet
root@(ve11a)(cfg-sync Changes Pending)(Active)(/Common)(tmos) list net self 172.28.20.11/24
net self 172.28.20.11/24 {
address 172.28.20.11/24
allow-service {
default
}
traffic-group traffic-group-local-only
vlan external
}
[root@ve11a:Active:Changes Pending] config tmsh
root@(ve11a)(cfg-sync Changes Pending)(Active)(/Common)(tmos) list net vlan external
net vlan external {
if-index 112
interfaces {
1.1 { }
}
tag 4094
}
ping to external host (172.28.26.70) from specific source ip (200.200.200.11)
[root@ve11a:Active:Changes Pending] config ping -c 3 -I 200.200.200.11 172.28.26.70
PING 172.28.26.70 (172.28.26.70) from 200.200.200.11 : 56(84) bytes of data.
^C
--- 172.28.26.70 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms
trace shows 4094 vlan and 200.200.200.11 source ip
[root@ve11a:Active:Changes Pending] config tcpdump -nni 0.0 -e icmp
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on 0.0, link-type EN10MB (Ethernet), capture size 96 bytes
08:01:43.130623 00:50:56:b3:1c:32 > 00:01:e8:d5:d4:47, ethertype 802.1Q (0x8100), length 102: vlan 4094, p 0, ethertype IPv4, 200.200.200.11 > 172.28.26.70: ICMP echo request, id 8024, seq 1, length 64
08:01:44.130039 00:50:56:b3:1c:32 > 00:01:e8:d5:d4:47, ethertype 802.1Q (0x8100), length 102: vlan 4094, p 0, ethertype IPv4, 200.200.200.11 > 172.28.26.70: ICMP echo request, id 8024, seq 2, length 64
08:01:45.129976 00:50:56:b3:1c:32 > 00:01:e8:d5:d4:47, ethertype 802.1Q (0x8100), length 102: vlan 4094, p 0, ethertype IPv4, 200.200.200.11 > 172.28.26.70: ICMP echo request, id 8024, seq 3, length 64
useless - need syntax for making ping work on LTM
SYNOPSIS ping [ -LRUbdfnqrvVaAB] [ -c count] [ -i interval] [ -l preload] [ -p pattern] [ -s packetsize] [ -t ttl] [ -w deadline] [ -F flowlabel] [ -I interface] [ -M hint] [ -Q tos] [ -S sndbuf] [ -T timestamp option] [ -W timeout] [ hop …] destination
no help there